MOARON Heater Focusing Reflector, Outdoor Heat Reflector Shield for Natural Gas Heaters and Propane Patio Heater, Directional Heat Reflector Protective Shield 1 Pcs

Price: $35.99
(as of Mar 30,2022 18:34:32 UTC – Details)

Product Description

About Heat Reflectors

The highly reflective, aluminum surface bounces heat like rays of light, similar to how a flashlight uses a reflector to focus light in the direction you point it. The durable construction of our reflector means you get quality you can count on for the life of your heater.

Extended Heat Range and Increased Performance
Make Your Propane Last Longer
Fits Most Full-Sized, Round, Gas, Patio Heaters

Patio Heater Reflector

Heat Focusing Reflector for Round Natural Gas and Propane Patio Heaters.The directional heat reflector, the protective cover of the outdoor terrace heater reflector, will be the most effective for heating a specific area.

Our heat focusing reflector redirects heat where you want it, protects trees and walls from unwanted exposure, and saves on propane. Enjoy the perfect amount of warmth, while using the minimum amount energy

High-temperature resistance
Highly reflective surface
Save energy
Use less gas/propane, protect the environment
Simple installation

INSTALLATION INSTRUCTIONS

STEP 1

Make sure the gap is large enough to fit the rim of the overhead reflector on your heater.

IMPORTANT: Prior to installation remove all packing material and peel film from the front side of the reflector. Do not remove the soft protective screw cap or the soft rectangular protective sleeve from the clamps. Those clamp protectors are made from high heat resistant materials. They are intended to stay on during use to increase clamp grip and help prevent scratches during installation.

INSTALLATION INSTRUCTIONS

STEP 2

Make sure the heater is cool and shut off or disconnect the gas source prior to installation. Locate the gas control knob on your patio heater. As shown in the diagram, position the middle clamp of your Heat reflector on the opposite side or approximately 180 degrees from the location of the gas control knob.

Place the rim of the heater’s overhead reflector into the middle clamp. Tighten the middle thumb screw until it is snug. Overtightening is not necessary and doing so may dent your heater.

Verify that the middle clamp of your Heat reflector is installed on the opposite side of the gas control knob as shown or adjust the location as needed. Failure to follow these instructions can result in heater damage and personal injury.

INSTALLATION INSTRUCTIONS

STEP 3

Gently bend either side of your Heat toward the heater until the rim of the patio heater enters the clamp on that side, then proceed by tightening the thumb screw until snug. Repeat the same thing for the other side and you’re all done!

Check the thumb screws often to make sure they have not loosened up and are still tightly fastened to the heater top.

To remove your Heat just follow these same steps backwards. Loosen the side clamps first and then remove your Heat after untightening the middle clamp. Just remember, never handle your Heat while it’s hot. Touching your Heat while hot can result in personal injury.

INSTALLATION INSTRUCTIONS

STEP 4

Always make sure all three clamps are fastened securely before turning on your patio heater. When ready to use, safely connect the gas and ignite your heater.

Keep in mind that your heater will now deliver much more heat than it did before. Proceed with caution and do not stand or sit too close until you know how it performs. It may be best to start off with low heat at first to make sure you do not overdo it. Slowly increase the heat until you’re comfortable.

Please remember to remove your Heat when not in use and do not have it installed in windy conditions above 5 miles per hour. If a heater is not properly secured there is a heightened risk of tipping.

Check Clamp Parts

Connect Middle Clamp

Fasten Side Clamps

Installation Completed

Tech Specifications

Height: 15 inches

Width: 35 inches

Weight: 2 lbs

Materials: Aluminum

Built to Last

Every Heat Reflector is made with high grade aluminum and machined with precision. With functional design leading way, is an absolute upgrade for your patio heater.

【Directional Heat Conduction】The directional heat reflector, the protective cover of the outdoor terrace heater reflector, will be the most effective for heating a specific area. Effectively control the temperature increase in the designated area
【Energy Conservation】 No matter where you are, you can adjust your angle according to your needs. It can reduce the invalid heat area by up to 50%. Save propane and natural gas, environmental protection
【Protect the Heater】 In light rain or snowy weather, the patio heater reflector on the top of the heater can protect the heater from rain or snow, which will extended the heater’s service life
【Easy to Install & Carry】 The heat focusing reflector is easy installation and is convenient to carry. Tools completely, one person can complete the installation
【Applicable Place】Heat reflector shield patio heater can make you feel warmer in winter. The heater reflector shield is suitable for any place, patio, bedrooms, windows, balconies, whether indoors, outdoors